An estimated one-rep max (e1RM) predicts the most weight you could lift once, calculated from a hard multi-rep set you completed. Enter a weight and rep count and this calculator shows the Epley, Brzycki, and Lombardi formulas side by side, plus the one estimate Kaltro uses for your e1RM trend and personal records. It is always an estimate — never a number to go and attempt.

One-rep max estimator

Unit

Enter a weight above 0 and a rep count of 1 or more to see the estimates.

The unit toggle changes the label only — enter your weight in whichever unit you picked, and the estimate comes back in the same unit. Nothing is saved; the whole calculation runs in your browser.

The three formulas, and what Kaltro does with them

Each formula converts a weight-and-reps set into a single-rep estimate a different way. They agree at low reps and pull apart as reps climb — which is why Kaltro stops estimating past 12 reps.

Epley

e1RM = weight × (1 + reps ÷ 30)

Reads higher than Brzycki below 10 reps; the two cross at 10 reps, after which Brzycki reads higher. Kaltro treats it as valid up to 12 reps.

Brzycki

e1RM = weight × 36 ÷ (37 − reps)

The denominator shrinks as reps rise, so it diverges sharply at high reps — never extrapolate it. Valid up to 12 reps.

Lombardi

e1RM = weight × reps0.10

A flatter curve: it reads higher than the other two at low reps and lower at high reps, as the table below shows. Shown for comparison only — Kaltro does not use it.

Kaltro’s estimate

This is the one estimate Kaltro uses, for your e1RM trend line and your e1RM personal record alike:

  • 1 rep: your e1RM is the weight you entered — a measured single, a data point rather than an estimate.
  • 2–12 reps: the average of Epley and Brzycki.
  • 13+ reps: no estimate. The formulas drift further from a tested single as reps climb, and Kaltro draws its line at 12. For an estimate, use a set of 12 reps or fewer.

How the e1RM trend works.

Worked example: 100 kg across rep counts

The same 100 kg lifted for more reps, run through every formula. Watch the formulas pull apart as reps climb, and Kaltro’s estimate stop at 12 reps.

Estimated 1RM in kilograms for 100 kg lifted at each rep count. The Epley, Brzycki and Kaltro columns match the app’s shipped formulas; Lombardi is shown for comparison only.
Set Epley Brzycki Lombardi Kaltro’s estimate
100 kg × 1 100.00 100.00 100.00 100.00 (your entered single)
100 kg × 5 116.67 112.50 117.46 114.58
100 kg × 10 133.33 133.33 125.89 133.33
100 kg × 12 140.00 144.00 128.21 142.00
100 kg × 15 Not valid past 12 reps Not valid past 12 reps 131.10 No estimate past 12 reps

Read this before you trust the number

  • It’s an estimate, not a measurement. An e1RM is a prediction from a submaximal set, not a max you tested. Two lifters with the same 5-rep set can have different true singles.
  • Accuracy degrades past about 10 reps. The more reps between your set and a single, the more the formulas disagree — see the worked example. Estimates from sets of 5 or fewer are the most reliable.
  • Never treat it as a number to attempt. An estimated single is for tracking and programming, not a cue to load the bar and test it. Kaltro never suggests testing an estimated max.
Where each formula is reliable, and where it drifts.
Formula Valid range in Kaltro Caveat
Epley 1–12 reps Reads higher than Brzycki below 10 reps; the two cross at 10.
Brzycki 1–12 reps Diverges sharply at high reps; never extrapolate.
Lombardi Not used by Kaltro Flat curve; shown for comparison only.

Let Kaltro track your e1RM for you

Log a set and Kaltro estimates it automatically, then charts your e1RM trend over weeks and months — no retyping. The trend uses the Epley-and-Brzycki average for sets of 1 to 12 reps.

Keep exploring: read the plain-English definition of estimated 1RM (e1RM), total a session with the training-volume calculator, browse all Kaltro calculators, or see how the app turns these numbers into a next-set suggestion. In the app, the trend and your PRs sit together — see strength progress in Kaltro.