How to run push/pull/legs in Kaltro
Push/pull/legs splits your week by movement pattern: a push day (chest, shoulders, triceps), a pull day (back, biceps), and a legs day. Kaltro ships all three as built-in day-templates — tap one to start that session, then run the rotation across your training week. This page shows what is in each day, how much to do, and how hard.
Lifters search for this as a “PPL program”; in Kaltro you run it as three day-templates you start one tap at a time. A split is a scheduling tool — the total volume and effort you put in over the week drive results, not the label on the day.
Who this is for — and who it isn’t
- Good fit: intermediate and advanced lifters who can train five or six days a week and recover from it. Running push, pull, and legs twice each over six days is where this split earns its high frequency.
- Not the best first split: if you are new to lifting, a full-body template three times a week builds the same base with less to manage. PPL is not a beginner default.
- Not for two-to-three days a week: below about five sessions, each muscle gets only one PPL day a week, so your weekly sets land at the very bottom of the range — a full-body or upper/lower split spreads the same three or four days better. If you can only train three or four days, use full-body or an upper/lower split instead.
- Returning from a long layoff or an injury: ramp the load back gradually and get clearance first (see the note at the end).
The three day-templates
Each of these is built into Kaltro as its own template — one tap starts that session. Set counts below are working sets (warm-ups are extra and are not counted by Kaltro’s analytics). Each template prefills a single rep target per exercise; the ranges shown are Kaltro’s defaults for a hypertrophy goal (or general fitness, or no goal set), and you fill the range before the weight goes up. Set a strength or endurance goal in your profile and Kaltro uses its ranges for that goal instead.
Push day — chest, shoulders, triceps
- Barbell Bench Press — 4 working sets, 8–12 reps
- Barbell Overhead Press — 4 working sets, 8–12 reps
- Incline Dumbbell Press — 3 working sets, 8–12 reps
- Dumbbell Lateral Raise — 3 working sets, 12–15 reps
- Cable Crossover — 3 working sets, 12–15 reps
- Cable Tricep Pushdown — 3 working sets, 12–15 reps
- Dumbbell Overhead Tricep Extension — 3 working sets, 12–15 reps
Pull day — back, biceps
- Bent Over Barbell Row — 4 working sets, 8–12 reps
- Lat Pulldown — 4 working sets, 8–12 reps
- Seated Cable Row — 3 working sets, 8–12 reps
- Cable Face Pull — 3 working sets, 12–15 reps
- Barbell Curl — 3 working sets, 12–15 reps
- Hammer Curl — 3 working sets, 12–15 reps
Legs day — quads, hamstrings, calves
- Back Squat — 4 working sets, 8–12 reps
- Romanian Deadlift — 4 working sets, 8–12 reps
- Leg Press — 3 working sets, 8–12 reps
- Leg Extension — 3 working sets, 12–15 reps
- Lying Leg Curl — 3 working sets, 12–15 reps
- Machine Standing Calf Raise — 4 working sets, 12–15 reps
How much: weekly volume in sets
Count training volume the simple way research tends to: hard sets per muscle per week. These are heuristics, not measured limits.
- A rough target is 10–20 hard sets per muscle per week for most intermediate lifters chasing size. Run twice a week, chest and quads each get 20 direct working sets — the top of that zone — and back gets 22, just over it. To bring back to 20, drop one set of Seated Cable Row on each pull day.
- It is a range, not a threshold. There is no exact number that is optimal, and more is not always better — returns diminish as sets pile up, and recovery is the real ceiling. Treat these as starting points to adjust by how you feel and perform.
- Add sets slowly. If you want more volume, add a set at a time and only once your recent weeks are being recovered from and progressed. The volume calculator totals a session for you.
How hard: effort, not failure
Most working sets should be genuinely hard but not maximal.
- Aim for about RPE 7–8 — two to three reps in reserve on most working sets. That is hard enough to drive adaptation while leaving room to recover and repeat.
- You do not need to take every set to failure. Training close to failure occasionally is fine; doing it on everything just deepens fatigue without a matching payoff.
- Log RPE if you want Kaltro to use it. It is optional — the app never invents an effort score — but when you log it, the suggestion engine reads it.
How to progress: reps first, then weight
Kaltro uses double progression — earn the reps at a weight before the weight moves.
- Fill the rep range, then add weight. When every working set reaches the top of its range at a controlled effort, add the smallest load your equipment allows and rebuild the reps.
- No fixed +2.5 kg-every-session promise. Progress comes when the sets say so, not on a schedule. See exactly how Kaltro decides when to add weight.
When to back off: deload by trigger
A deload is a planned lighter stretch — but plan it by signal, not by the calendar.
- Reduce when performance says so: Kaltro reads three signals from your log — reps sliding at the same weight, a long time away, and logged effort staying high across consecutive sessions. It does not read sleep: if a run of poor nights leaves you flat, backing off is your call. Then drop volume or load for a spell and rebuild.
- Not “every fourth week” by default. Kaltro calls deloads from your logged trends, never a fixed date — see when Kaltro calls a deload.
The spreadsheet (and a CSV-import demo)
Two separate things — keep them straight.
- To run the split, use the built-in templates. They are already in Kaltro; tap Push, Pull, or Legs to start that session. You do not import anything to get them.
- The CSV is a plain spreadsheet of the movements above, and a way to try Kaltro’s generic CSV import, which turns each row into a history entry you then fill in. It does not install a reusable template — the built-in ones already do that.
- Weight and rep cells are intentionally blank so you enter your own loads in your own units. The file carries the structure; you bring the numbers.
This is general education, not medical advice. If a movement causes pain, or you are returning from injury or a long layoff, check with a qualified professional before loading it.
Run it with the reasoning shown
Start a push, pull, or legs template in Kaltro, log your sets, and the app suggests the next step — and shows you why, from the sets you logged, on your device.
Other splits: upper/lower and full-body three times a week. Terms in plain English: progressive overload and working set. To train from these in the app, or write your own, see templates and workouts in Kaltro.